Rear Window Storage Molle Panel Flank Kit Rear Window Protective Decoration for Ford Bronco

Just installed these on both sides of my Bronco Raptor after confirming with the manufacturer via email that they would fit the Raptors. Very happy with the finished result, they appear to be made of good quality material that should hold up well. I really like the added functionality to mount roto-pak gas cans, jacks, shovels, etc outside the truck cab, and I think they look great. Now the downside. I had a very difficult time installing these. In fact, I gave up and took my Bronco to my local Ford dealer and their tech's did the work. It turns out that my kits (both drivers side and passengers side) were shipped with just the single style upper mounting clamps. There are supposed to be two different sizes of upper clamp. A wider one for the front and a narrower one in the back. I got four narrow ones. Needles to say the front upper clamps were not wide enough to clamp the on the hard top and the dealer techs had to make up about a 3/8" spacer and powder coat it and get longer bolts to get the front clamps to fit to the roof (see picture). The bottom mounts that screw into the Broncos body panels did fit but were a real challenge to get right. They sit between the hard top and the rear fender body panels and they do hold the hard top up a little bit from resting all the way down against the top of the rear fender panel but it doesn't appear to be enough to allow water in. All in all, happy with the purchase but be advised, the install can be very challenging and the single instruction page is not great.

If you own a 2024, description says these will work, nope.

This Molle panel is awesome once installed! The hardest part of this product is the install because the directions were not as clear as I’d like. I’ll list step by step instructions: Open package ( inside contents to include) 1 Molle panel 1 page of instructions 1 small box with brackets and screws. Remove panels over driver and passenger doors. Loosen large panel over back seats and move aside. Unsecure hard top screws to be able to manipulate the hard top. Pay attention to instruction page!!! Look at the two top brackets labeled 1 and 2. #1 is bigger /longer than number #2. The first bracket to be installed is #1. At the top of the bracket is some screws that need to be unscrewed in order to expand the bracket. Place bracket at the top of your hard top above front portion of the window, and the lower part in the groove about the actual window. Then tighten screws to secure. #2 bracket -loosen screws and place bracket in the closest to the rear of the hard top. Now put the lower portion of the bracket in groove just above window and tighten screws to secure bracket. So at this point two top brackets should be installed. (See photos provided) Bottom brackets: Option1- So, what I did is I lifted the left rear portion of the hard top and place the brackets between hard top and Bronco body; I used the weight of the top to secure the brackets. Option 2- The instructions show the brackets fixed to the body and secured with provided screws. You can use provided screws in the box to screw in top portion of the bottom bracket and they will apply pressure securing it to the body. Next, Remove screws from lower brackets and hold until Molle panel is able to matched up with top and lower brackets. Screw panel to top and bottom brackets. Use the provided screws in brackets to secure panel. Once panel is secured you can attack anything that you like. I have these rubber latches and I placed my recovery shovel as a demo. I like this concept and I like this panel. I just think the instruction page with six pictures aren’t sufficient enough for this install. Keep in mind I’m reviewing the product and overall I’m pleased with the purchase. I’d give the product installation instructions just 3 stars. I’d give the product a five star rating product!!!!

This is for the DRIVERS side only. INSTALL Pretty straightforward thanks to a previous review. You will need to screw the bottom brackets with the pre existing screws under the rear of the hardtop. He mentioned using the weight of the top to secure it but I wouldn’t recommend that, definitely use the pre existing screws to secure those bottom brackets. OVERALL It is extremely sturdy, hard to tell how the finish will hold up. Looks great, makes the side profile of the truck a lot more appealing. I will be adding traction boards soon. Only 4 stars because they need to be more clear that this will only fit the drivers side!

Perfect Addition to My Bronco! I recently bought the backside window rack for my Ford Bronco on Amazon and it’s been fantastic. The installation was straight-forward and it fits perfectly. It's sturdy and holds my gear securely, making it easier to organize my cargo. Plus, it looks great and matches the rugged style of my Bronco. Highly recommend!