Blu Resin (1kg) High Strength/Impact Resistant Tough Resin for 3D Printer (Clear V2)

使ってみたところ、かなり感度が高いようです。 普通のABS Likeレジンと同じ時間で造形すると、剥離時にプリンタが揺れるくらいフィルムに強力に張り付いてしまい、造形物が歪みますし、ゲル状のゴミが発生してしまうようです。 ELEGOOのMars 3 Proだと初期層20秒、以降1.5秒くらいの設定だときれいに造形できるようです。 臭いとの評価でしたが、私が使ったクリアV2は改善されたのか大したことがなく、SK本舗のABS Likeレジンより臭いは弱いくらいです。 まあ、換気しないと使えないのは変わりませんが。。。

堅牢ですね、やはり力がかかるところにはコレ。 ただ、ドリルしていたりすると薄いところがパキッとあっけなく割れることもあり、もう少し粘りがあったら最強なのですが。 （粘りがあるから割れるのか？？） クリアV2は無色透明なのでやはり使いやすいです。 とはいえ若干の黄色味はあります（写真参照）ので期待しすぎない方がいいです。 Chitubox用の設定ファイルをSiraya公式からダウンロードできるのは大変良いです。 露光時間が長すぎたりすると、ゲル状のゴミが出たり造形不良（寸法出ないとか）になりやすいので、上手くいかない方は上記設定ファイルのパラメータを使ってみることをおすすめします。

The resin works great for parts that need to resist impacts, but the smell is actually the worst and curing times is a huge pain

I can't sing the praises of this resin enough. Not only does it print beautifully, but you can get all the details you'd ever want just by being careful with your layer exposure settings (< time = more details). You can get any amount of flexibility/hardness depending on the amount of time spent curing. 5 minutes or less of curing, and it's so flexible that it's basically a nylon. 5 to 10 minutes of curing it's not nearly as flexible, it gets harder but still doesn't break easily. It took me 30 minutes of curing to get it to a point where I could snap off supports with my fingers; anything less than that, a good pair of toenail clippers will be required. Ideal print settings on a Creality HALOT MAGE (regular, not pro) are 0.25mm layer size. 1s light delay. 2 - 3s per layer with 3 to 5 bottom layers at 10 to 30s, depending on the weight of the model. At 10s, you can easily just tug firmly, and it comes right off the build plate. At 30s, I was using a metal spatula and a rubber hammer to get it off, (it still didn't break, but I did have to completely realign my print head). If you want a really cool effect, mix this 50/50 with the Sunlu "abs-like" resins in blue or red. It also mixes so well with other resins. It's my go-to resin to fix other resins. I even used this to fix the super crappy Yousu silver resin. I wish I could buy this stuff by the drum. Long story short, this is the best resin I've ever tried, and completely worth the money. *I use the AnyCubic Wash and Cure 3 for curing, but you can also cure in direct sunlight, and the properties get really interesting.

Again, imo high quality resin. Since it's clear, you can color it with special pigments which is wha I did and it turned out very good. One thing to note - it is rather thick, almost like honey, but it gets runnier with heat, but not that much. Just so you know.

Great resin, one of the best for engeneering parts

Great resin for miniatures. I mix in 15% with standard resin for added toughness. Haven’t had one break falling off the table for a while!